SamL Colt 1851 Navy Octagon Barrel - The Firearms Forum
网页2024年9月15日 · I hate to break this news to you but all 1851 Colt revolvers had a brass grip frame. Civilian models were silver plated brass and government military contract Colts had plain brass grip frames. Trying to clean it up or restore it will probably remove value from it rather than enhance it.
How to repair gap on original 1851 Colt Navy
网页2018年4月12日 · To check the correct arbor fit to the arbor recess in the barrel lug, remove the barrel slightly and rotate it enough off of the frame pins, reinstall to see what the frame clearance is. If it is zero clearance add a .002 shim washer into the barrel lug, reassemble the pistol, and check.
Short Barreled 1851 Navy - Colt Forum
网页2017年5月5日 · Short Barreled 1851 Navy. I have a Colt 1851 Navy manufactured in 1852. The barrel length is 5 1/16 inches. I know that Colt did manufacture, to special order, 1851 Navies with differing barrel lengths. How do you tell if the barrel was actually manufactured by Colt or if it was shortened from the standard 71/2inch barrel.
Original 1851 Navy barrel dimension? | Colt Forum
网页2017年11月5日 · I don't now about the original 1851 Navy .36, but DGW lists the Pietta 1851 Navy as having a tapered barrel with .710" at the breech and .625" at the muzzle. I suppose it is measured across the flats but I don't know that as a fact.
Colt Revolvers That Have Been Tightened Up, Or As Originally …
网页2018年3月20日 · Looking at the rear of this barrel, the upper part of the cut is in a radius (around the bore) that fits perfectly with the frame curvature below the cylinder. Perhaps some of you have other examples of Colt 1851 Navy's that show this same procedure was used to refine the barrel-to-frame fit.
1851 Colt Navy barrel wedge (removing) | Gunboards Forums
网页2009年4月20日 · I was wondering what is the best way to remove the barrel wedge from the Colt Navy pistol. The directions say to use a wooden or plastic wedge, but they will not budge it. What is the best method to use without using a metal wedge?
Tuning Up the New 1851 Colt Navy - Graybeard Outdoors
网页2013年5月16日 · The barrel wedge was nearly impossible to remove, and mis-fires were becoming all to common. After a close inspection I found two very obvious problems. 1- There was a lot of slop in the cylinder between the barrel and the frame, which is the reason for the mis-fires. The cylinder was moving far enough forward that the …
Colt 1851 Navy Revolver, .36 caliber, 7-1/2" barrel, silver plated ...
网页The .36 caliber Model 1851 COLT brand Navy revolver is beautifully finished, with a blued octagon barrel, polished blued cylinder, color case hardened frame and loading lever, silver plated brass back-strap and triggerguard, and reddish brown walnut grips. This used revolver has some handling marks.
Colt 1851 U.S. Navy-Navy Richards-Mason Conversion .38 LC …
网页Make: Colt. Model: 1851 Navy with Centerfire Richards-Mason Conversion. ... Action Type: 6-Shot, Single Action, Side-Gate Loaded Revolver. Markings: The top of the barrel is marked “-ADDRESS SAML COLT NEW-YORK CITY-”. The underside of the barrel lug is marked “58822”. The frame, trigger guard, backstrap, underside of the cylinder arbor ...
Antique 1861 Colt Navy Conversion, caliber .38 rimfire, 7-1/2" barrel …
网页This is an original Richards-Mason conversion revolver that was produced by the Colt factory in the mid-1870's to shoot .38 rimfire cartridges. In 1871 Colt employee Charles Richards was awarded a patent for converting 1851 and 1861 Colt Navy percussion revolvers to a breech loading cartridge revolver.
- 某些结果已被删除