How to upgrade tuners on a Fender P-bass - TalkBass.com
网页2006年5月10日 · That's 40% of the Fender tuners' weight - a 60% reduction. Knocking that much weight off the headstock feels like an even bigger reduction because it's on the far end of the neck and disproportionally skews the perceived bass mass toward the end. That causes neck dive and unnecessary discomfort while playing a long gig.
Squier Affinity P Bass tuners upgrade - TalkBass.com
网页2012年10月26日 · That will eliminate a number of options. Most Fender/Squier basses have holes in the headstock that are 11/16" in diameter and are meant to take tuners with a 1/2" post. The Highway One tuners' diagram says they have 1/2" posts, which are usual for Fenders. This means they'll work with just about any headstock with 11/16" drilled holes.
Tuner Headstock Hole Size MIM 2010 PBass - TalkBass.com
网页2000年3月26日 · Hi- Can anyone tell me what size tuner hole I need to order for for a 2010 MIM Fender P-Bass? I want to put black tuners on it but don't want to order the wrong size (I did that on a franken bass before - wasn't pretty...) :crying: Thanks, all!
Tuning Peg replacement for Fender P bass - TalkBass.com
网页829. New Mexico. Mar 21, 2018. #1. So I've been mulling over replacing the tuning machine heads on my P bass. The stock ones are old and can't keep the bass in tune after 30 mins of jamming. I have a 2010 MIM model and I've narrowed it down to these 3. Hipshot HB7, Schaller, or Gotoh FB30. The hipshots seem the most practical since they're a ...
Do all Fender tuning machines fit all of their necks?
网页2012年10月8日 · Feb 17, 2021. #7. This is actually a bit of a nightmare. After HOURS of exhaustively searching google, I have found that only 1 aftermarket replacement is a direct fit for MIM necks, the Hipshot HB7. The other one that fits is the Fender Highway One bass tuner, which is what I am going to get since it's stock.
Fender headstock hole size? - TalkBass.com
网页2006年1月21日 · The preferred way to mount them is to drill a 9/16" dia hole through the headstock, and then use a special reamer to cut a 11/16" dia counterbore on the front side, to a depth of about 3/8". That way, the 9/16" hole on the back side helps to support the post and keep the whole tuner centered in the bushing. So, many necks do have a 9/16" hole ...
Tuners for a Squier P-Bass? - TalkBass.com
网页2007年5月13日 · Oct 21, 2016. #20. TJBass said: I know most of the squier bass are different in many ways, but I installed a Hipshot BT7 Dtuner key on my affinity P and it was a drop in replacement. I'm sure if I had wanted or needed to replace all the tuners that the hipshot HB7's would be pretty much a direct replacement.
light tuners for Mexi Fender P-bass? - TalkBass.com
网页2003年5月11日 · Feb 13, 2014. #1. I have an American P-bass Special which comes with Mexican tuning machines. At 7.8 lbs the bass has a little neck dive. Does anyone make lighter tuners to replace the Mexican Fender hardware? When I researched this about 8 years ago the Hipshot Ultralites didn't fit the Mexi Fender holes. Has this changed?
Fender MIM Replacement Tuners? - TalkBass.com
网页8. Visit site. Aug 14, 2005. #2. I've done the tuners on two of my MIM basses. I used Schaller BML tuners. They were $46.00 from Warmoth. I was able to leave the stock bushings in-didn't feel the need to change the current ones, and besides, they look pretty close to the vintage style. I did have to make some new holes, but it's not hard to do.
Tuners and Bridge for Squier Affinity Jazz | TalkBass.com
网页251. Mar 14, 2017. #7. I just replaced the bridge and tuning mechs on a brand new Squier Affinity PJ bass just two weeks ago, so hopefully this info helps you. The tuning mech holes were slightly bigger than 1/2". I know this because my …